- Middy's TechEnergy
- Courses Available
- Certificate III in Instrumentation and Control (Volt Edge)
Middy's Contractor Training
- Middy's Training Overview
- Training Registration
- Courses Available
- Lifestyle Control / Automation
- Philips Dynalite System Design
- KNX Basic Certification (NECA)
- Wiser™ Smart Home Automation Intro (Schneider Electric)
- Industrial
- Certificate III in Instrumentation and Control (Volt Edge)
- Certificate IV in Electrical - Instrumentation (Volt Edge)
- Certificate IV in Hazardous Areas Electrical (Volt Edge)
- High Voltage Switching (Volt Edge)
- Qualified Business Person (Volt Edge)
- Qualified Technical Person (Volt Edge)
- CCTV
- CCTV Certification Program Level 1 (Dahua)
- Intruder Alarm & CCTV (Comtech)
- Data Comms
- Practical IP Networks for Contractors
- Combined Cabling Endorsement (Comtech)
- ACMA Open Cabling Licence (Comtech)
- Certificate III in Telecom Technology (Comtech)
- Certificate IV in Telecom Engineering Technology (Comtech)
- MATV
- Digital Terrestrial Reception Systems (Matchmaster)
- Solar & Battery Storage
- Solar Grid Connect 5 Day (NECA)
- Battery Storage 6 Day (NECA)
- Solar Grid Connect 5 Day (Volt Edge)
- Battery Storage 4 Day (Volt Edge)
- Energizer Homepower Technical Installation
- Electric Vehicle Charging
- Electric Vehicle Charging Equipment Intro (NHP)
- Electric Vehicle Charging Equipment Intro (Schneider Electric)
- Security
- ECO-System Products Intro (HikVision)
- BOSCH Alarm Panel 2000/3000
- Lighting Control
- DALI-2 Room Lighting Solution (Theben)
- Fundamentals of Light
- Air Movement Introduction (Ventair)
- General Lighting and Design Principles (Pierlite)
- Air Conditioning
- Certificate II in Split Air-conditioning and Heat Pump Systems (Volt Edge)
- Certificate III in Split Air Conditioning and Heat Pump Systems (Volt Edge)
Certificate III in Instrumentation and Control – UEE31220
The Certificate III in Instrumentation and Control – UEE31220 course provides you with the skills and knowledge to select, install, set up, test, fault find, repair and maintain systems and devices for measurement and recording of physical/chemical phenomenon and related process control.
-
Presenter:
Volt Edge Trainer
-
Time:
Dates and times to be advised by Volt Edge.
-
Venue:
QLD: 3/739 Nudgee Rd, Northgate QLD 4013
VIC: 5/262 Wolseley Place, Thomastown VIC 3074
NSW: 2/320 Parramatta Rd, Burwood NSW 2134
-
Training dates:
Middy's will register your interest for this course with our Partner trainer as a preliminary registration. The Partner trainer will then contact you directly to complete your registration and organise payment.
Dates and times to be advised by Volt Edge.
Course Details:
Duration and Mode of Delivery:
Stage 1: Theory
Theory completed online self-paced. Hours vary pending required units per students (roughly 120hrs).
Stage 2: Practical
Practical completed in our Brisbane, Sydney or Melbourne training centre. Intensive practical assessment requiring students to utilise our live functioning equipment to meet the requirements of the training package and gain valuable hands on experience. Final capstone assessment includes 2 attempts with a further charge of $500 per day/attempt as required. You are not eligible for an outcome until practical is completed.
Course Cost:
Contact our Training team with a copy of your USI transcript from www.usi.gov.au for a quote.
Middy's will register your interest for this course with our Partner trainer as a preliminary registration. The Partner trainer will then contact you directly to complete your registration and organise payment.
Disclaimer: Courses are run subject to availability and enrollment numbers. Course dates may change subject to participant availability and ensuring minimum class sizes are filled. Courses non-refundable, alternate course dates will be provided if required.